HYDRIL K20 Pulsation Bladders / Dampener and Bladder Kits

IPD^TM – PPD (Production Pulsation Dampener Diaphragms

Hydril Type “K” Pulsation Dampener: Popular Mud Pump Spare Parts: Below is a partial list of mud pump spares, mud pump replacement parts, and mud pump parts that we have available. Fluid End Discharge Module Fluid End Studs & Nuts Full Open Valves Gardner Denver Lower Valve Guide Gland Brass And Junk Rings Gland Nut Ideco Mm-700 Duplex. The Hydril K-P Series Pulsation Dampener/Surge Stabilizer should be mounted in the vertical position (refer to Figure 1- 3 and 1-4 for mounting options) with the mating flange con- nection at the bottom. The discharge dampener should be mounted as close as possible to the discharge port of the pump. Flowguard USA is your online source for information regarding Flowguard Ltd. Pressure vessels which are used to solve hydraulically induced pulsation, vibration or rapid surge problems. Flowguard’s vessels can be found in a number of industrial sectors including Oil & Gas, Chemical, Pharmaceutical, Food & Beverage, Pulp & Paper, Waterworks. Inddition to the ZM pulsation dampener Coorstek offers:. Inline gas-charged pulsation stabilizers. Appendage-type stabilizers. FlowGuard® pulsation dampers. Replacement bladders and repair kits:. Continental Emsco® PD-45, PD-50. Hydril® K-Series, IP-Series ZM-SERIES PULSATION DAMPENER VOLUME ZM-12. 3.9 gallons (14.7 liter).

Replacement Diaphragms and Stabilizer for K-10 and K-20 Pulsation Dampeners. Hydril Type 'K' Pulsation Dampener Aftermarket Parts. Rig Manufacturing, LLC 281-909-7447 www.rigmanufacturing.com sales@rigmanufacturing.com. Item Description Qty 10 Gallon 20 Gallon Weight/Lbs.

IKD^TM – DPD (Drilling Pulsa tion Dampner Diaphragms)

Hydril Pulsation Dampener Manual

© 2019 Rubber Regenerating & Processing Co. Powered By BTN Infosolution

SFU Series

1. SFU o-ring
2. SFU wing nut
3. Dust cap
4. Loading valve
5. Bleeder valve
6. Cartridge
7. Case

SFV & SFVM Series

1. 6″ or 8″ suction gasket
2. 6″ or 8″ grooved coupling
3. Dust cap
4. Loading valve
5. Bleeder valve
6. Cartridge
7. Case

SFT Series

1. HPG-1 gasket (Nitrile or EPDM)
3. Dust cap
4. Loading valve
5. Bleeder valve
6. Cartridge
7. Case

Train simulator free content. SFM Series

1. SFM o-rings (2 required)
2. SFM wingnut
3. Dust cap
4. Loading valve
5. Bleeder valve
6. Cartridge
7. Case
8. SFM wingnut screw

CHARGE TO 80%- 90% OF SUCTION PRESSURE OR THE MAXIMUM CHARGE PRESSURE OF THE CARTRIDGE, WHICHEVER IS LESS. THIS IS ONLY AN APPROXIMATION.

(YOU MAY FIND IT NECESSARY TO DECREASE THE PRESSURE IN THE SUCTION CARTRIDGE TO ACHIEVE OPTIMUM PUMP PERFORMANCE.)

1. Shut down pump and relieve line pressure from discharge side before closing suction valve. After discharge line is relieved of pressure, close suction line valve and drain suction line.
2. Open bleeder valve ’A’.
3. Remove loading valve protector cap ’B’.
4. Remove cap from loading valve ’C’.
5. Loosen safety nut ’D’ three full turns.
6. Using NITROGEN ONLY, charge the cartridge through loading valve ’C’ to the recommended operating pressure (90% of suction pressure). (DO NOT EXCEED MAXIMUM CARTRIDGE CHARGE PRESSURE).
7. Tighten safety nut ’D’ on loading valve ’C’.
8. Replace loading valve protector cap ’B’
9. Open suction valve. When air from bleeder valve ’A’ is evacuated, close bleeder valve ’A’.

1. Shut down pump and relieve line pressure.
2. Open bleeder valve ’A’.
3. Remove loading valve protector cap ’B’.
4. Remove cap from loading valve ’C’.
5. Loosen safety nut ’D’ three full turns.
6. Using NITROGEN ONLY charge the cartridge through loading valve ’C’ to correct charge pressure (use chart below).
   NOTE: DO NOT EXCEED MAXIMUM CARTRIDGE CHARGE PRESSURE (ON CASE LABEL).
   
7. Tighten safety nut ’D’ on loading valve ’C’ and replace cap.
8. Replace loading valve protector cap ’B’.
9. Open suction valve. When air from bleeder valve ’A’ is evacuated, close bleeder valve ’A’.

WARNING

THE USE OF ANY GAS OTHER THAN NITROGEN IS EXTREMELY DANGEROUS.

NEVER ATTEMPT TO CHARGE OR PRE-CHARGE A CARTRIDGE OUTSIDE OF THE PULSATION STABILIZER CASE.

FOR PROPER CHARGING PROCEDURES REFER TO THE SUCTION OR DISCHARGE CHARGING GUIDE.